Where do I find the key code or the original keyless entry code to reset my keyless code on an 01 Explorer? - key code flightsimulator
I have the keys and forget the code for keyless entry, my Explorer Sport Trac 2001 (parked for a while). Well, where do I find the key code so that you get a key cut by a dealer or you can find the code for my keyless entry (door to reset)? Thank you!
Sunday, February 7, 2010
Key Code Flightsimulator Where Do I Find The Key Code Or The Original Keyless Entry Code To Reset My Keyless Code On An 01 Explorer?
8 comments:
must be manual, but if not, you say you are:)
in the tailgate, no code should be, or just go to a company
I hope he finds his keys for now. If you've noticed, I found some websites that different things about how you say reset the code key .... I have an Explorer Sport 01 in my manual, there is a plastic card the size of a credit card, leads him. (I have my code again, I stood in stamping codes for a while and finally I turned around and got it. You did not say how long hoped the truck, then j, that this problem and to remember. It was also very nervous when I forgot and took a deep breath to relax and, as I said before I started to the numbers that I remember made.
-------------------------------------- ...
Ugh! I'm debating whether to get it to the dealer as meaningful, it's the code for $ 70 to? It took about 2 1 / 2 hours, but that's mainly because the instructions were not very specific about the location of the MSC (Computer Security Modules). If I just knew where to start could have the task completed in 20-30 minutes. Here, the abbreviation is for others to follow:
It is in the passenger side in a position behind the rear door is plastic and below each cut. I screwed on the side of the court and is under the lower deck.
Step 1 - Remove the rubber door seal loose from the bottom all in the back of the door opening and nearly half at the top.
Step 2 - Place the two metal clips on the upper part of the rear doors are open.
Step 3 - Remove the brackets after the piece of higher court (where the belt off) drawing on the back edge. There are 3 clips from there to the rear.
Step 4 - Identify the last clip in the middle at the top.
Step 5 - Remove part of the adaptation process, you pulled down on the back of the room and. It is a metal "guide" at the top of the front of the opening of the seat belt will have to see.
Step 6 - Remove the metal clip is now operating in the lower part of plastic cutting board to the doorway. It is at the bottom of theOpen the door.
Step 7 - Remove the top of the lower frequency limit of the plastic as you can see the MSM screwed to the wall behind him. The MSC is the black box about 5 inches wide and 4 "high and 1 inch deep. Do something between the seat and the piece of metal from the edge of the door wedge to give you the hands free.
Step 8 - Now you have a free hand, the scope of the MSC and drag the bottom of the module to turn on us a little so that you can see the label on the front side. The 5-digit code is the last 5 digits in a bar code. 5 The figures themselves are grouped, in order to recognize them.
Step 9 - Now, before you put it all cut, went to the driver's side door and test the code, if it works.
Step 10 - Put in reverse order. DONE!
************************************** ...
Some models have the key code behind the passenger headlight on the module (I do not say, tBases his right, by chance, the hood is not locked)
If you can not change / set the code works, but you can program your personal code, if you have), the plant code (or your personal code ... Here's how:
1. Enter the factory (or) set personal code (lights up the keyboard when pressed).
2. Press 1 / 2 within 5 seconds step 1
3. Enter your new) (5 personal code numbers. Enter the numbers in the 5-seconds of the previous.
The Manual: Put a code consists of three equal numbers and it shows in the order that these kinds of code easier to understand. (It is not permitted.)
Your personal code does not replace the factory code. You can either open the car. When you enter a personal code on the other side, the module will erase the first personal code for new code.
To finish, press will be 7 / 8 9 / 0 or together, allowing more than 5 seconds elapse since the touch of a button, and there was a 5-digit code key programmed"."
If you can not come to call the toll-free help and training from them the VIN number and they can say what you need to know about your browser
It needs to your owner's manual for a white plastic card. In the absence of which is placed on a sticker on the RAP (Remote Anti-theft Personality) module. Behind the plate is to fit behind the rear seats. To access the module requires the removal of the panel to get a clear view. There must be a "black box" with two connections that secured with two screws. The five-digit code that appears on the label. You need the dealer to obtain information from your key-code, if you should get them your VIN reduced because not only the new key, but well-planned (using your vehicle's PATS key). It's like they have to get your code keyless entry, and if you're here. Sorry, but there is no way around it.
Check your owner's manual or it to the dealer and it was reset.
FORD specifically to COM tab search, or the main dealer for help. perhaps at a price of $ 35 really just a PC that is loaded by the code, and changed his birthday to the best of luck
should be in your owner's manual or you can contact the manufacturer and ask them to
Post a Comment